2nd generation black 1979 Chevrolet Camaro 572 BBC For Sale

US $22000

Send Inquiry Read T.O.S[<-Click] before sending inquiry! Also, some sellers can't be contacted by email (inquiry). Check at the bottom of this vehicle ad for info.

Vehicle Summary

Mileage-

AvailabilityYes

Year of Manufacture1979

FuelGasoline/Petrol

Vehicle Detail

2nd generation black 1979 Chevrolet Camaro 572 BBC Z28 For Sale.

Selling my 1979 camaro Dart 572 BBC, Msd programmable igntion, 4l80e with programmable US shift, Ford 9 inch, tubular suspension. Have receipts for everything including still a parts warranty on the motor build, Over 50k invested only 2000 miles on build. Selling because I need the money for a nice daily. Car is 100% streetable. Hate to sell it but I am not in a position to keep it. You will not be disappointed!

Detailed desciption

Almost everything on the car is new outside of the body. All components were carefully picked The body is solid. The complete drivetrain has only 2100 miles on it and the motor has 1 year of warranty ( parts) left!

The car runs and drives great as is and is VERY STREETABLE unlike a lot of other “street-strip” cars out there that only have 3 speed transmissions, spools etc

Here is an almost complete list of parts-components installed from front to back. Receipts from parts totals alone are upwards of $40k, NOT including any labor, paint OR the cost of the car itself…
B&M Super-plate trans cooler
Dillon 4 core aluminum radiator with two 12″ SPAL fans
All new steering components, QA1 tubular upper and lower control arms, coil overs and tie rod ends
C5 Corvette spindle and disc conversion
Manual steering box conversion
Race Star 92 black chrome 17″ wheels all the way around..
ALL bushings replaced with Energy Suspension poly, body mounts engine-trans, suspension etc etc

572 BBC- Built with Dart Sportsman block ( standard height will clear a booster if you want to put one back on), SCAT 4340 forged crank and H beam rods, Wiseco forged pistons, ARP2000 rod bolts, Comp Cams hyd roller cam, tie bar lifters, Heads built with all comp cams hardware, Comp pro magnum rockers, melling oil pump,ARP bolts all around,SFI balancer and flexplate, single plane intake, taylor green wireset, engine was dyno’d and have video to show
CVF Racing 8 rib serpentine setup, aluminum high flow water pump
Powermaster 250 Amp alternator, 1 gauge cables, battery in trunk
Hedman headers- Ceramic coated NO mods needed to fit
MSD Programmable 6al,black pro billet distributor and coil

GZ sportsman vacuum pump

Domintaor Gen 3 1050

Manual brake conversion

Jakes Performance Stage 3 4L80 ( 1000hp capable) transmission with OVERDRIVE! and a low gear transbrake
Upgraded to stage 3 level with 300M billet input shaft locally
Controlled by US Shift quick 4 controller which is FULLY PROGRAMMABLE by your laptop and easy to use program. Set shifts wherever you want, switch to a manual mode etc, way better than self learning
PHD triple billet lockup converter, stall speed is around 4700, which is good on the street for it
G force F body 4L80 crossmember
Action Machine Aluminum driveshaft, rated over 2000 hp, sonnax slip yoke,1350 U Joints
Autometer Gauge package and tach all converted to LED lights, custom aluminum panel
B&M Quicksilver gate/ratchet shifter with transbrake button on handle
Pioneer Bluetooth stereo and front speakers installed in kick panels
Power windows
AC/heat system and vent tubes removed
S&W 8 point roll bar completely welded in and also tied into Heidts subframe connectors, roll bar has extended rear bars to save the back seat
Scat pro car seats and G force camlock 5 point harnesses, rear seats newly covered, new rear interior plastics

Tanks INC fuel tank with Magnafuel 500 fuel pump with custom sump
All braided feed and return lines
Mickey Thompson ET Street R Drag Radials
Pypes Race pro Mufflers and true 3″ duals

Strange overbuilt 9″ rear setup – powdercoated housing, Daytona pinion setup, Detroit truetrac differential, US gear 3.89 ring and pinion, 35 spline axles with access holes drilled, Wilwood street disc brake setup, Caltrac traction bars, Summit leaf springs, Energy suspension shackles, new spring mount plates

Paint was JUST completed. Matrix system black base/triple coat clear. Has 1 little ding in the drivers side door and a few very minor chips. looks excellent.

Roll bar is only an 8 point, if you don’t want it you can cut it out in an hour! Throw some bucket seats and a new uncut carpet back in it and will look stock again!

Receipts for everything!!! i know i’m forgetting something but if you have any questions don’t hesitate to ask!!

Asking $22,000 or best offer

If you’re interested call or text me for all the Details and more pictures.

Contact phone – 248-431-3388 – (use phone number only, don’t send inquiries – contact by email is not available).

Car located in – Auburn Hills, Michigan, US.

Makes: 1979-1981 Chevy Camaro.

Send To Friend

Send Inquiry