Light blue 1986 Chevrolet Camaro with rebuilt motor For Sale

Vehicle Detail

Light blue 1986 Chevrolet Camaro with rebuilt motor For Sale.

What a car! The motor came out of a 1968 Z 28. The motor has been completely rebuilt, hi out put 327 motor 400+ hp stock 441 heads comp mother thumper cam, keith black positions, Pete Jackson gear drive ◆New holly ivader carb / everything possibly has been done with it. pushing 500 horsepower! Transmission 700 R 4 tranny with fresh rebuild and shift kit, 411 gears and 377 gears, new tires on front and inda glow air shocks in the rear. Body clean, no body filler not a bad car at all! Need to see! Street / Rod was $8900.00 Now $7500.00

Ackerly & Childs 9771-45 gap-to-fit moly rings $130.00
AFR 1095 195cc SBC Eliminator Comp cylinder heads $2,079.00
8041 1.580-inch solid roller valve spring upgrade $207.00
8508 titanium retainers $129.00
ARP 134-2501 balancer bolt $27.00
134-3703 12-point High Performance head bolts $138.00
434-2101 12-point stainless intake bolts $39.00
134-5402 main studs $52.00
134-7901 oil pump drive shaft $13.00
Autolite AR3910 spark plugs $40.00
BEP 70082 front cover $35.00
Canton 15-246 SBC F-body RR Power Pan $48.00
20-013 SBC pickup 3/4-inch tube $40.00
Comp Cams 12-773-8 solid roller cam $367.00
818-16 solid roller lifters $430.00
1105-16 Hi-Tech stainless rocker arms $480.00
Eagle S/R 6000SBLW 6-inch I-beam rod $299.00
Engine Tech CC400 cam bearings $17.00
EP155 oil pump, 3/4-inch pickup $33.00
Federal Mogul/Fel Pro 1010 0.039-inch head gaskets (2) $146.00
1206S-3 intake gaskets $33.00
TCS45121 front cover gaskets $13.00
1880 one-piece oil pan gasket $43.00
138M 10 race main bearings $98.00
8 7065CH 10 race rod bearings $90.00
2912 rear main sEAL $31.00
GM N/A stock replacement 327 balancer $100.00
14011012 water pump $130.00
327 CI build sheet
JGM Performance Engineering
(labor on 1964 327ci two-bolt main block)
thermal clean and magnaflux block $108.00
bore and hone block with dual-torque plates $308.00
align and hone main journals with ARP studs $188.00
regrind & micropolish factory steel small-journal crank $134.00
balance rotating assembly $250.00
custom blueprint and assemble long-block $850.00
dyno test and tune $750.00
KB Performance KB155 +40 pistons $454.00
Manley 25716-16 5/16-inch, 0.080-inch wall
pushrods (+0.200) $180.00
Moroso 60461 cam button $18.00
93020 valve cover gaskets $62.00
MSD Ignition 83645 digitial HEI Module $182.00
8225 HEI Coil $117.00
Pro Gear PG4100-1TB timing set, 1/2-inch pitch with
Torrington bearing $150.00

Total $9,475.00

Contact phone – 763-208-7254 – Also, can send inquiry (contacting by email).

Car located in – Ramsey, Minnesota 55303, US.